Whig Rose

Continuing with overshot, I wove two table runners (or maybe more accurately, one loooooong runner, and one table square/topper) in the Whig Rose design from A Handweaver’s Pattern Book by Marguerite Porter Davison.

I used Venne organic 2/16 cotton in cream for the warp and tabby weft.  2/8 organic cotton in Brick Red was used for the pattern weft in the red runner, and a 2/8 mercerized cotton that shall remain nameless was used for the green one.  The organic cotton is a high quality cotton with great twist and is wonderful to weave with.

At 54.5″ long, the red runner would suit a long harvest table (which must of been what I was thinking, hence its long length), it would look great as the centrepiece of a holiday table setting.  The green one is 20.5″ long and would make a great table square for the centre of a smaller table.

whig-rose-7

 

whig-rose-4

Happy weaving,

Kelly

 

Organic Cotton Towels

I recently decided to try the 315-4 towels I wove here again, paying attention to the notes I made last time when I wove them.  Although I had said that  I didn’t like the stripes, I tried them again, only weaving have the repeat in the alternating colour, much better.

These towels are woven with Venne 2/8 organic cotton, (2/16 for the hems).  They washed and dried beautifully and are very soft.

2003-12-31 014

2003-12-31 0202003-12-31 019

 

 

 

 

 

 

 

 

2003-12-31 016

2003-12-31 017
2003-12-31 018

 

 

Happy weaving,

Kelly

 

 

Third Time’s A Charm

Back when I was weaving the overshot runner (see here), I met a much more experienced weaver and I told her my tale of woe on this project.  We discussed a few possibilities and then she asked what yarn was I using for my warp, “Oh” she said, “you never use their mercerized cottons for warp, they don’t have enough twist”.  Ironically, that was what I thought when this yarn arrived, but this company sells weaving yarns, and still being a new”ish” weaver, I could be wrong.  I had e-mailed them about my problems, they refused to acknowledge that it could be their yarn.  Hence the project was cut from the loom.

The problem with not really knowing what the source of the problem is, is that you don’t know what the source of the problem is (yarn, loom, weaver).  I went through my stash and discovered some 2/16 non-mercerized cotton, mostly likely from the same company as the mercerized.  The first thing I noticed was that there was definitely more twist in this yarn.  I didn’t use the organic 2/16 cotton I just brought in because I was still unsure whether it was the yarn or my weaving technique that had caused the earlier problems.

I started winding the warp, things were going well, and then nearly at the halfway point, a knot.  About 3 yards later, another knot.  In total, I encountered 5 knots while winding this short warp, I was not impressed.  I soldiered on and got the warp on the loom, threaded the heddles, sleyed the reed and began to weave.  And weave.  And weave.  Miraculously, no broken threads, I felt vindicated.

This runner was fun and quick to weave and I will definitely do it again.  I love the fineness of the 2/16 (pattern weft is in 2/8 cotton), the runner has an almost heirloom feel to it.

2003-12-31 004

2003-12-31 002

Happy weaving,

Kelly

 

I Give Up

I decided to revisit the overshot runner project with the 2/16 mercerized cotton warp.  But instead of trying to continue on the existing warp, I decided to make a new warp and put it on another loom.  I made a shorter warp than before, only about 3 yards, using a warping board.  Since this loom has a plain beam, the warp was beamed in the usual manner.  I also replaced all of the existing heddles with brand new inserted eye heddles.  I wanted to see if these changes would provide me with a more pleasurable weaving experience (i.e. no broken threads).

Things seemed to progress okay, but then 3″ into the pattern, the first thread broke.  After another inch, one more, and after another inch, well you get the idea.  I have now woven 20″ and have repaired 11 broken threads.  I am not getting any joy out of this project.  I love the pattern, I love weaving overshot, I love the colour combination, I hate this yarn.  I am not thrilled with the 2/8 mercerized cotton I am using for the weft either.  It seems to be loosely plied and twists on itself and around the tabby yarn as well.

So here is a shot of it before I cut it off the loom.  I have to find a use for the remaining 2/16 (fire starter?), and when I find a better quality yarn, I will try this project again.

DSCN3399

Happy weaving,

Kelly

Overshot Runner Part 3: Sloooooooow Progress

I have finally reached the end of the first runner for this warp, or maybe the end of the last, depending on how I feel.

Overshot Runner 025

This has been the warp from hell for me.  The spools themselves had knots, but the biggest annoyance has been warp threads breaking.  I have searched on-line, started a discussion on Ravelry, and have spoken with more experienced weavers to determine the possible cause (me, loom, thread), but it is hard to come up with a clear answer.

Overshot Runner 028

The breakages have occurred after I have advanced the warp and tensioned it.  Could there be too much tension on the warp?  Well maybe, but after comparing mine to others, my tension is not any tighter (and probably a bit looser) than those I compared it to.

One thought I had was maybe the metal heddles were too rough for the 2/16 mercerized cotton I am using.  However, that was met with a bit of skepticism from my weaving group, mercerized cotton is  supposed to be stronger than unmercerized cotton (I was going to replace the metal heddles with Texsolv, but I will hold off on that for now).  This is the first time I have used anything as fine as 2/16, but should that really make a difference other than it takes longer to weave 36″ in 2/16 versus 2/8?

The majority of the broken threads are in one area.  This warp consists of one entire spool of 2/16 mercerized cotton and part of a second.  Selvedge threads were added after the warp was put on and came from the second spool, all of my repair threads have come from the second spool, and now one of those repair threads has broken.  What does this all mean?  Could it be a bad spool of cotton?  Maybe.

Other than the broken threads, I have enjoyed weaving with the 2/16 mercerized cotton.  I love the sheen that the cotton has and the heirloom look it gives the runner.  If anyone has any other ideas as to what my problem might be, I would love to hear from you.

Happy weaving,

Kelly

Overshot Runner Part 1: Warped

Now that I am familiar with the technique of overshot, I have decided to weave some more runners on my home loom.

I found a draft that I like from the Leclerc Looms website.

(photo from Leclerc website)

(photo from Leclerc website)

Pattern Details:

  • 2/16 cotton for warp and tabby weft
  • 2/8 cotton for pattern weft
  • 30 epi
  • 16″ wide in the reed
  • 480 ends

I am using a sectional warp beam, something I’m not that familiar with.  Since I am only doing a small warp (6 yards), I needed to figure out how to get my warp on.  I decided to wind 16 warp chains, 30 ends each.

warp chains

warp chains

And, thinking I was being clever, wound them all on at the same time.  Note to self:  do not do that again.  I did however, use a warping valet/trapeze to maintain a nice tight tension while winding on, and I will definitely do that again.  The following picture shows the warp chains coming from the back of the loom, under the front beam and up to the valet (aka broom handle in the floor joists).  After this picture was taken I removed the front beam because it wanted to pop off.

Overshot Runner 009The warp chains were weighted with bottles of water:

Overshot Runner 010

Three warp threads broke while I wound on the warp that will have to fixed, not too bad I think.

This is how the warp looks from the back of the loom:

Overshot Runner 013

and tied onto the front apron rod:

Overshot Runner 014

Now to start weaving!

Happy weaving,

Kelly